Firmware Updates for Inverters with Display
Version Date - July 2020
Release notes for:
StorEdge systems, excluding systems with Powerwall 1 batteries
StorEdge systems with Powerwall 1 batteries – please open a support case here.
SolarEdge systems without StorEdge
| Products | CPU | DSP1 | DSP2 |
|---|---|---|---|
| Single Phase Inverter with HD-Wave Technology | 3.2537 | 1.0.1036 | 2.0.910 |
| Single Phase Inverter without HD-Wave Technology | 3.2537 | 1.210.217/1.210.1427 | 2.52.507 |
| Three Phase Inverter (up to 33.3kW) | 3.2537 | 1.13.1644 | 2.19.1427 |
Battery's firmware versions
| Battery | Type | ID | Version |
|---|---|---|---|
LG Chem RESU 7H/RESU 10H | LG DCDC | 5010/7010 5020/7020 | 5.4.6/7.4.6 5.4.8/7.4.8 |
| LG BMS | 100 | 1.4.6 |
Devices' firmware versions
| Device | CPU | Controller |
|---|---|---|
| CCG | 3.2537 | N/A |
| Wireless Gateway | 3.2537 | N/A |
| Energy Meter | N/A | 0.71 |
| Smart Energy Hot Water | 3.10041 | 0.12.98 |
Release notes
New Features and Enhancements
For North America installations –
- Support for cellular modem (LTE)
- Support for UL1741 PCS ESS export only mode
Fixes
- When system production < 200W, PV production values in the monitoring platform's power flow diagram might show 0 (the energy charts production values are not affected)
Known Issues
- "Status: OK" and "TCP failure error" are displayed alternatively in the Server Communication Status screen of inverters with cellular modem if the connection with the SolarEdge server failed.
Workaround: If your network has a firewall, you may need to configure it to the following address to enable the connection:- Destination Address: prod.solaredge.com
- TCP Port: 22222 (for incoming and outgoing data)
- "No SIM Card" error will be displayed if SIM is inserted after power-up.
Workaround: Perform AC cycle
Important notes
- If DSP1 version >= 1.210.600 it will upgrade to version 1.210.1427
- If DSP1 version >= 1.210.24 (and < 1.210.217) it will upgrade to version 1.210.217
- Use Firefox or Chrome browsers to download firmware files.
- The firmware file can only be loaded to a memory card that meets the specifications listed in the Software Upgrade using SD/MicroSD card application note.
https://www.solaredge.com/sites/default/files/upgrading_an_inverter_using_micro_sd_card.pdf - For Japan installations – do not upgrade JET certified (SE5500H-JPJ) inverter versions. If further information is required, please contact SolarEdge Support.
| Products | CPU | DSP1 | DSP2 |
|---|---|---|---|
StorEdge Single Phase Inverter without HD-Wave Technology | 3.2618 | 1.210.1427/1.210.1623 | 2.52.507/2.52.615 |
Battery's firmware versions
| Battery | Type | ID | Version |
|---|---|---|---|
LG Chem RESU 7H/RESU 10H | LG DCDC | 5010/7010 5020/7020 | 5.4.6/7.4.6 5.4.8/7.4.8 |
| LG BMS | All | 1.4.6 |
Devices' firmware versions
| Device | CPU | Controller |
|---|---|---|
| Energy Meter | N/A | 0.71 |
| Smart Energy Hot Water | 3.10041 | 0.12.98 |
Release notes
New Features and Enhancements
- For North America installations:
- Support Backup Interface, SolarEdge's new Flexible Backup Solution
- Support for cellular modem (LTE)
- Support for UL1741 PCS ESS export only mode
Fixes
- Improved firmware upgrade process
- For Australia installations – the battery is not forced to charge when its SoE is below the minimum defined, while smart energy devices are prioritized higher than battery charging
Important notes
- StorEdge single phase inverters' DSP1 and DSP2 will upgrade to firmware versions 1.210.1623 and 2.52.615 respectively
- Use Firefox or Chrome browsers to download firmware files.
- The firmware file can only be loaded to a memory card that meets the specifications listed in the Software Upgrade using SD/MicroSD card application note.
https://knowledge-center.solaredge.com/sites/kc/files/upgrading_an_inverter_using_micro_sd_card.pdf
For SetApp enabled inverters firmware click here